以匠心致初心，秉承着责任与使命，豫信致诚机械设备(本溪市分公司)恪守“信誉是根本，质量是生命”的经营理念，以诚实、守信、稳健态度，创新 混凝土抛丸机产品研发，严把质量关口，用一颗真诚、感恩之心对待每一位客户。
BW软管泵的基本结构<br />
往复泵由动力段和液力端两大部分组成。<br />
动力端的功能，是将动力机的回转运动转变为活塞(或柱塞)的直线往复运动。它包括传动离合装置、变速减速装置和曲柄连杆。它们的相互位置与安排决定着泵的总体结构型式，决定着泵的驱动方案及结构方案的选择。动力端的主要零部件包括皮带轮，离合器曲轴箱体及其中的传动轴，齿轮副，曲轴，连杆及十字头滑块。<br />！
保养泵的方法：
1、泵注意绝缘电阻，长期搁置不用的或在潮湿环境中使用的电动抽液泵，使用前必须用500伏兆欧表测量绕组的绝缘电阻。
2、泵和电动油桶泵应经常检查，维修，在检查时,必须检查电源线：内接线，插头，开关是否良好，绝缘电阻是否正常，刷尾座是事松动，换向器与电刷接触良好，电枢绕级扩定子绕组是否是有适中断路现象，轴承及转动零件是否的损坏等等。
3、经常加脂，电动油桶泵为高速运转，润滑脂易于挥发，所以必须使轴承处的润滑能保持清洁，并注意添换。
工业软管泵不锈钢齿轮泵，可输送非润滑油饮料低腐蚀性液体，配铜齿轮可输送汽油苯等低内点液体。由于齿轮泵自吸能力差，一般是由于齿轮泵泵腔间隙较大所致。同时也是如果齿轮泵输出端没有“止回阀”，则必须是下一级齿轮泵的止回阀或控制阀。移动固定后，周围工作人员可恢复手术。
Industrial hose pump stainless steel gear pump, can transport non-lubricant beverages with low corrosive liquids, with copper gears can transport gasoline, benzene and other low internal point liquids. Due to the poor self-priming ability of the gear pump, it is generally caused by the large gap between the pump cavity of the gear pump. At the same time, if there is no "check valve" at the output of the gear pump, it must be a check valve or control valve of the next gear pump. After moving and fixing, the surrounding staff can resume surgery.
众所周知软管泵在运行时，是通过一根U型附有弹性的橡胶软管来完成输送。今天小编需要强调的是，软管存放时间不宜过长，一般以一年为限。在停工期间，对装有软管的泵，若长期不用，每隔一个月需转动泵一次。以免压辊长时间压在泵管的某一处，减弱管子回弹性，影响其流量的输送。
It is well known that when the hose pump is running, it is conveyed through a U-shaped rubber hose with elasticity. Today the editor needs to emphasize that the storage time of the hose should not be too long, and it is generally limited to one year. During the shutdown period, if the pump is equipped with a hose, if it is not used for a long time, the pump needs to be rotated every other month. So as not to press the roller for a long time at a certain position of the pump tube, it will weaken the resilience of the tube and affect its flow rate.